![]() Kansas Attorney General Kris Kobach answers questions during a news conference about a new state law that defines male and female in state law so that transgender people can’t change their driver’s licenses and birth certificates to reflect their gender identities, Monday, June 26, 2023, at the Statehouse in Topeka, Kansas.To determine which style you have, look underneath the fixture where the shower wall meets the tub spout. Step 3: Use a 1/8" hex/Allen wrench and un tighten the Allen screw counterclockwise.3 of 5 |. ![]() Step 2: Unscrew the tub spout in a counterclockwise rotation until the tub spout is removed off of the brass adapter. Step 1: Remove any caulking around the wall end of the tub spout with a putty knife or razor. The customer had a double handle manifold in place and preferred a single handle manifold, so the company replaced it. Approximate labor cost: $1,200 for 16 hours of labor. Standard fit Ovation tub (33.75 inches by 60 inches by 75 inches): $500. Ovation bathtub and installation: $2,000 from Jeremy Foster of Maintenance Solutions in Olathe, Kansas.Now, measure the new bathtub pipe by placing it next to the old pipe. Measure the drain hole from the inside of the tub to the surface the tub rests upon. Remove the bathtub and set the tub down on a hard, balanced surface.Mark the drainpipe riser at the correct height, then remove the drain pan and trim down the drain pipe. First, test-fit the shower pan and note the position of the drain pipe riser extending up through the drain opening. Follow the manufacturer's directions to install the shower pan. According to the report, Christmas Tree Shops took out a $45 million loan, but creditors terminated it "after the company defaulted on the terms due to worsening revenues and liquidity." Install the Shower Pan.The wide cost fluctuation is mainly the result of the type of bathtub chosen. While the average national cost to replace a bathtub is $5,660, it can run as little as $750 or as much as $20,000.Watco does not recommend and does not warranty this product when oil/petroleum based plumber’s putty is used when installing this product.While the average national cost to replace a bathtub is $5,660, it can run as little as $750 or as much as $20,000. The QuickTrim® Kit including bathtub stopper and Innovator® overflow is now securely in place.ĬARE OF PRODUCT FINISH: Do not use abrasive or caustic cleaning agents, as they may discolor or permanently damage the finish of the product.Ĭleaning should be done using warm soapy water, applied with a clean soft cloth and dried with a clean soft cloth. Snap the Innovator® overflow plate onto the retainer ring, making sure the opening on the overflow plate is facing down towards the tub (Figure 4). Secure adapter bar with screws and retainer star nut (behind adapter) to overflow elbow (Figure 3). Ĭonvert existing 1-hole and 2-hole overflow plates to the Innovator® Snap-on Overflow Plate! Remove existing overflow plate. Insert New Bathtub Stopper! The QuickTrim bathtub drain and bathtub stopper, with its bright new finish is now securely in place (Figure 2). Determined by the drain, place either the thin or thick “O” ring on the ridge of the drain for a “snug fit” and Place the supplied QuickTrim® drain body (Figure 1) over the old drain. Remove the existing stopper, leaving the drain in the bathtub. * Will fit existing Watco drains with cross-bars. ![]() It’s that Simple! Purchase a Watco QuickTrim® Kit anytime you decide to change the look of your bathtub drain, stopper and overflow. The QuickTrim® comes with a matching bathtub stopper and Innovator® snap-on overflow plate. Right into the existing drain with no mess! Want a quick way to change the look of your bathtub finishes? Replace with a Watco QuickTrim® Kit.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |